In physics and engineering, a phasor (a portmanteau of phase vector^{[1]}^{[2]}), is a complex number representing a sinusoidal function whose amplitude (A), angular frequency (ω), and initial phase (θ) are timeinvariant. It is related to a more general concept called analytic representation,^{[3]} which decomposes a sinusoid into the product of a complex constant and a factor depending on time and frequency. The complex constant, which depends on amplitude and phase, is known as a phasor, or complex amplitude,^{[4]}^{[5]} and (in older texts) sinor^{[6]} or even complexor.^{[6]}
A common situation in electrical networks is the existence of multiple sinusoids all with the same frequency, but different amplitudes and phases. The only difference in their analytic representations is the complex amplitude (phasor). A linear combination of such functions can be factored into the product of a linear combination of phasors (known as phasor arithmetic) and the time/frequency dependent factor that they all have in common.
The origin of the term phasor rightfully suggests that a (diagrammatic) calculus somewhat similar to that possible for vectors is possible for phasors as well.^{[6]} An important additional feature of the phasor transform is that differentiation and integration of sinusoidal signals (having constant amplitude, period and phase) corresponds to simple algebraic operations on the phasors; the phasor transform thus allows the analysis (calculation) of the AC steady state of RLC circuits by solving simple algebraic equations (albeit with complex coefficients) in the phasor domain instead of solving differential equations (with real coefficients) in the time domain.^{[7]}^{[8]} The originator of the phasor transform was Charles Proteus Steinmetz working at General Electric in the late 19th century.^{[9]}^{[10]}
Glossing over some mathematical details, the phasor transform can also be seen as a particular case of the Laplace transform, which additionally can be used to (simultaneously) derive the transient response of an RLC circuit.^{[8]}^{[10]} However, the Laplace transform is mathematically more difficult to apply and the effort may be unjustified if only steady state analysis is required.^{[10]}
Phasor notation (also known as angle notation) is a mathematical notation used in electronics engineering and electrical engineering. can represent either the vector or the complex number , with , both of which have magnitudes of 1. A vector whose polar coordinates are magnitude and angle is written ^{[11]}
The angle may be stated in degrees with an implied conversion from degrees to radians. For example would be assumed to be which is the vector or the number
Euler's formula indicates that sinusoids can be represented mathematically as the sum of two complexvalued functions:
or as the real part of one of the functions:
The function is called the analytic representation of . Figure 2 depicts it as a rotating vector in a complex plane. It is sometimes convenient to refer to the entire function as a phasor,^{[12]} as we do in the next section. But the term phasor usually implies just the static complex number .
Multiplication of the phasor by a complex constant, , produces another phasor. That means its only effect is to change the amplitude and phase of the underlying sinusoid:
In electronics, would represent an impedance, which is independent of time. In particular it is not the shorthand notation for another phasor. Multiplying a phasor current by an impedance produces a phasor voltage. But the product of two phasors (or squaring a phasor) would represent the product of two sinusoids, which is a nonlinear operation that produces new frequency components. Phasor notation can only represent systems with one frequency, such as a linear system stimulated by a sinusoid.
The sum of multiple phasors produces another phasor. That is because the sum of sinusoids with the same frequency is also a sinusoid with that frequency:
where
or, via the law of cosines on the complex plane (or the trigonometric identity for angle differences):
where .
A key point is that A_{3} and θ_{3} do not depend on ω or t, which is what makes phasor notation possible. The time and frequency dependence can be suppressed and reinserted into the outcome as long as the only operations used in between are ones that produce another phasor. In angle notation, the operation shown above is written
Another way to view addition is that two vectors with coordinates [ A_{1} cos(ωt + θ_{1}), A_{1} sin(ωt + θ_{1}) ] and [ A_{2} cos(ωt + θ_{2}), A_{2} sin(ωt + θ_{2}) ] are added vectorially to produce a resultant vector with coordinates [ A_{3} cos(ωt + θ_{3}), A_{3} sin(ωt + θ_{3}) ]. (see animation)
In physics, this sort of addition occurs when sinusoids interfere with each other, constructively or destructively. The static vector concept provides useful insight into questions like this: "What phase difference would be required between three identical sinusoids for perfect cancellation?" In this case, simply imagine taking three vectors of equal length and placing them head to tail such that the last head matches up with the first tail. Clearly, the shape which satisfies these conditions is an equilateral triangle, so the angle between each phasor to the next is 120° (2π⁄3 radians), or one third of a wavelength λ⁄3. So the phase difference between each wave must also be 120°, as is the case in threephase power.
In other words, what this shows is that
In the example of three waves, the phase difference between the first and the last wave was 240°, while for two waves destructive interference happens at 180°. In the limit of many waves, the phasors must form a circle for destructive interference, so that the first phasor is nearly parallel with the last. This means that for many sources, destructive interference happens when the first and last wave differ by 360 degrees, a full wavelength . This is why in single slit diffraction, the minima occur when light from the far edge travels a full wavelength further than the light from the near edge.
As the single vector rotates in an anticlockwise direction, its tip at point A will rotate one complete revolution of 360° or 2π radians representing one complete cycle. If the length of its moving tip is transferred at different angular intervals in time to a graph as shown above, a sinusoidal waveform would be drawn starting at the left with zero time. Each position along the horizontal axis indicates the time that has elapsed since zero time, t = 0. When the vector is horizontal the tip of the vector represents the angles at 0°, 180°, and at 360°.
Likewise, when the tip of the vector is vertical it represents the positive peak value, (+A_{max}) at 90° or π⁄2 and the negative peak value, (−A_{max}) at 270° or 3π⁄2. Then the time axis of the waveform represents the angle either in degrees or radians through which the phasor has moved. So we can say that a phasor represent a scaled voltage or current value of a rotating vector which is “frozen” at some point in time, (t) and in our example above, this is at an angle of 30°.
Sometimes when we are analysing alternating waveforms we may need to know the position of the phasor, representing the alternating quantity at some particular instant in time especially when we want to compare two different waveforms on the same axis. For example, voltage and current. We have assumed in the waveform above that the waveform starts at time t = 0 with a corresponding phase angle in either degrees or radians.
But if a second waveform starts to the left or to the right of this zero point, or if we want to represent in phasor notation the relationship between the two waveforms, then we will need to take into account this phase difference, Φ of the waveform. Consider the diagram below from the previous Phase Difference tutorial.
The time derivative or integral of a phasor produces another phasor.^{[b]} For example:
Therefore, in phasor representation, the time derivative of a sinusoid becomes just multiplication by the constant .
Similarly, integrating a phasor corresponds to multiplication by . The timedependent factor, , is unaffected.
When we solve a linear differential equation with phasor arithmetic, we are merely factoring out of all terms of the equation, and reinserting it into the answer. For example, consider the following differential equation for the voltage across the capacitor in an RC circuit:
When the voltage source in this circuit is sinusoidal:
we may substitute
where phasor , and phasor is the unknown quantity to be determined.
In the phasor shorthand notation, the differential equation reduces to
Solving for the phasor capacitor voltage gives
As we have seen, the factor multiplying represents differences of the amplitude and phase of relative to and .
In polar coordinate form, it is
Therefore
With phasors, the techniques for solving DC circuits can be applied to solve linear AC circuits. A list of the basic laws is given below.
Given this we can apply the techniques of analysis of resistive circuits with phasors to analyze single frequency linear AC circuits containing resistors, capacitors, and inductors. Multiple frequency linear AC circuits and AC circuits with different waveforms can be analyzed to find voltages and currents by transforming all waveforms to sine wave components (using Fourier series) with magnitude and phase then analyzing each frequency separately, as allowed by the superposition theorem. This solution method applies only to inputs that are sinusoidal and for solutions that are in steady state, i.e., after all transients have died out.^{[13]}
The concept is frequently involved in representing an electrical impedance. In this case, the phase angle is the phase difference between the voltage applied to the impedance and the current driven through it.
In analysis of three phase AC power systems, usually a set of phasors is defined as the three complex cube roots of unity, graphically represented as unit magnitudes at angles of 0, 120 and 240 degrees. By treating polyphase AC circuit quantities as phasors, balanced circuits can be simplified and unbalanced circuits can be treated as an algebraic combination of symmetrical components. This approach greatly simplifies the work required in electrical calculations of voltage drop, power flow, and shortcircuit currents. In the context of power systems analysis, the phase angle is often given in degrees, and the magnitude in rms value rather than the peak amplitude of the sinusoid.
The technique of synchrophasors uses digital instruments to measure the phasors representing transmission system voltages at widespread points in a transmission network. Differences among the phasors indicate power flow and system stability.
The rotating frame picture using phasor can be a powerful tool to understand analog modulations such as amplitude modulation (and its variants ^{[14]} ) and frequency modulation.
, where the term in brackets is viewed as a rotating vector in the complex plane.
The phasor has length , rotates anticlockwise at a rate of revolutions per second, and at time makes an angle of with respect to the positive real axis.
The waveform can then be viewed as a projection of this vector onto the real axis.


(Eq.1) 
Since this must hold for all , specifically: , it follows that


(Eq.2) 
It is also readily seen that
Substituting these into Eq.1 and Eq.2, multiplying Eq.2 by and adding both equations gives
Q.E.D.
Wikimedia Commons has media related to Phasors. 
Wikiversity has a lesson on Phasor algebra 